|
FireBlock136 Residential
Fire Block |
 Nsi FireBlock136 fire Blocking caulk is a single component, non
combustible material for residential applications. Colored Red for
easy inspection, FireBlock136 creates and effective barrier against
flames, smoke, and toxic gasses and has superior adhesion and gun
ability. Fire Block 136 is for use in annular spaces around wires
and pipes, ducts, vents and other penetrating items at ceiling and
floor openings; and room to room in wood and steel frame
constructions.FireBlock136 exceeds ASTM E136 standards for
fire blocking residential requirements prescribed by all major-model
building codes, and also meets or exceeds requirements of UBC, BOCA,
SBC, IRC, NYS and MA codes. FireBlock136 meets UL 1479 and ASTM-E814
standards.
** Please note
these products
are Ground Shipped Only **
|
| Cat
# |
Description |
Spec's |
Quantity
Discount |
Purchase |
| FS-136 |
10.3 fl. oz. cartridge |
View |
1-11 $6.05 |
12+ $5.45 |
|
|
FireStop814 Residential and
Commercial Fire stop |
 Nsi FireStop814 fire stopping caulk is a single component, non
combustible, non-intumescent material for residential and commercial
applications. Colored Red for easy inspection, FireStop814 creates
and effective barrier against flames, smoke, and toxic gasses and
has superior adhesion and gunnability. FireStop814 is for use in
annular spaces around wires and pipes, in one and two hour fire
rated assemblies. It restores the integrity of firestops in
residential and commercial construction. FireStop814 meets UL
1479 and ASTM E814 standards.
** Please note
these products
are Ground Shipped Only **
|
| Cat
# |
Description |
Spec's |
Quantity
Discount |
Purchase |
| FS-814 |
10.3 fl. oz. cartridge |
View |
1-11 $9.39 |
12+ $8.45 |
|
|
FireStop Box Guards |
NSi
FireStop Box Guards are one component fire rated pads made of highly
intumescent firestop material for use in electrical boxes. They are
inserted in the box and adhere to the inside back wall. NSi FireStop
Box Guards are easy to install and very cost effective. When exposed
to fire they expand, forming a char that will seal off the opening,
prevent the spread of fire and limit the temperature rise on the
unexposed surfaces. When used as directed, the horizontal separation
between outlet boxes on opposite sides of the wall may be less than
24 inches, provided that the boxes are not back-to-back. NSi
FireStop Box Guards are classified by UL under Wall
Opening Protective Material as found in the Fire Resistance
Directory. Available in two sizes to suit single and double boxes.
STC Rating 55.
View Spec's Here
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
| FSBG-1 |
Single Gang Box Insert |
1-24 $6.98 |
25+ $6.28 |
|
| FSBG-2 |
Double Gang Box Insert |
1-24 $7.88 |
25+ $7.08 |
|
|
FireStop Cover Guards |
NSi
FireStop Cover Guards are one component fire rated
gaskets made of highly
intumescent firestop material for use in electrical boxes.
They are mounted on the inside of the cover plate and installed at
the same time as the cover plate. When exposed to fire they expand,
forming a char that will seal off the opening, prevent the spread of
fire and limit the temperature rise on the unexposed surfaces.
NSi FireStop Cover Guards are easy to install and very cost
effective. Excellent for use when addressing the 24 inch rule.
They are used when electrical
boxes are installed in rated walls facing opposite directions
and horizontally separated by less than 24 inches. They can also be
used as a solution for standard
electrical boxes when the 100 square inch rule is violated.
Exceptional for safe, retrofit applications. Can be used for both
metal and plastic cover plates. NSi FireStop Cover Guards are
available as single switch,
double switch, single receptacle, single decorator and double
decorator. An economical alternative to putty pads. STC
Rating 54.
View Spec's Here
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
|
FSSRC |
Single gang
receptacle guard |
1-24 $4.98 |
25+ $4.48 |
|
|
FSDRC |
Double gang
receptacle guard |
1-24 $5.98 |
25+ $5.38 |
|
|
FSSSC |
Single gang
switch guard |
1-24 $4.98 |
25+ $4.48 |
|
|
FSDSC |
Double gang
switch guard |
1-24 $5.98 |
25+ $5.38 |
|
|
FSSDC |
Single gang
decorator guard |
1-24 $4.98 |
25+ $4.48 |
|
|
FSDDC |
Double gang
decorator guard |
1-24 $5.98 |
25+ $5.38 |
|
|
Fire Stop Intumescent Caulk |
 Intumescent Caulk is water based, single component elastomeric
sealant intended for use as a fire stop system component. It forms
an economical yet durable, flexible and watertight bond with most
construction materials. It is applied independently for "caulk and
walk" systems or over mineral wool or backer rod to seal the
openings where building services such as pipes and cables penetrate
fire rated assemblies. Will not crack or crumble as the physical
properties remain stable over time. it tolls easily and cleans up
with water. may be applied by caulking gun or trowel.
ASTM E 814 and UL 1479 View Spec's Here
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
| FSIC-10 |
10.3 fl. oz. cartridge |
1-11 $14.64 |
12+ $13.18 |
|
| FSIC-20 |
20
oz. foil sausage pack |
1-11 $29.87 |
12+ $26.88 |
|
| FSIC-45 |
4.5
gallon pail |
1-4 $712.95 |
5+ $677.30 |
|
|
Fire Stop Silicone Caulk |
 Nsi FireStop Silicone is a primerless, single component silicone
sealant. The sealant cures to a durable, flexible rubber when
exposed to atmospheric moisture. It is designed for economical use
in joint and service penetration firestop configuration and form a
watertight bond with most construction materials. In most cases, no
primer is required. It may be applied over a wide temperature range,
0 deg. F to 120 deg. F (-18deg. C to 50 deg. C) It will remain
flexible indefinitely between temperatures of -50 deg. F and 300
deg. F. May be applied by caulking gun or trowel.
ASTM E 814 and UL 1479 View Spec's Here
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
| FSS-10 |
10.3 fl. oz. cartridge |
1-11 $14.64 |
12+ $13.18 |
|
| FSS-20 |
20
oz. foil sausage pack |
1-11 $29.87 |
12+ $26.88 |
|
| FSS-45 |
4.5
gallon pail |
1-4 $712.95 |
5+ $677.30 |
|
|
Fire Rated Putty Sticks and
Putty Pads |
FIRE RATED PUTTY STICKS
AND
PUTTY PADS
NSi Fire Rated
Putty is a moldable non-curing, one-component fire rated material
for through penetration fire stop systems. In the event of a fire,
NSi Putty will expand when exposed to fire, forming an insulating
char, which prevents the spread of flames, smoke, gas and water
through penetration openings. Installation is easy as there are no
additives, there is no mixing and no curing time is required. The
putty is applied by hand and adheres to all common building
surfaces. NSi Putty can be installed in confined or occupied spaces
since there are no volatile solvents or asbestos fillers.
NSi Putty systems are rated up to 3 hours in accordance
with ASTM E 814, UL 1479 and ULC/CAN4-S1 1 5-M standards. NSi Fire
Rated Putty is available in sticks or pads.
View Spec's
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
| FSPS |
1-1/2" x 10" putty Sticks |
1-11 $28.29 |
12+ $25.46 |
|
| FSPP-1 |
6"
x 7" putty pads |
1-19 $7.09 |
20+ $6.37 |
|
| FSPP-2 |
7"
x 7" putty pads |
1-19 $8.09 |
20+ $7.27 |
|
|
FireStop Mortar |
 NSi
FireStop Mortar is a single component non-combustible fiber
reinforced, foamed cement mortar. It is intended to
provide economical, non-combustible and tight-fitting firestops at
openings and penetrations through fire-rated wall and floor
assemblies. NSi FireStop Mortar powder mixes easily to form a
shaving cream-like, non-slumping paste. This feature permits easy
installation with a minimum of damming.
When cured, NSi FireStop Mortar is self-supporting and there-fore
may be used for large openings where other fire stopping materials
are impractical. It requires and contains no solvents and is
comprised of materials of low toxicity. it mixes and trowels easily
and tools are cleaned with water. Dust protection is recommended.
The color is a distinctive charcoal (dark gray). ASTM E 814 and UL
1479 View
Spec's Here
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
| FSM |
FireStop Motar in 15.5 lb. bags |
1-4 $99.75 |
5+ $89.77 |
|
|
FireStop Pillows |
 NSi
FireStop Pillows are a single step firestop system component.
They are intended for wall and or floor openings through fire separations
where temporary or permanent firestops are required. They
are ideal where cable retrofitting is frequent and anticipated.
These
pillows allow for quick and clean single product installation.
Pillows
are self-supporting no wire lath or mesh is required. They are to
be packed tightly into the voids between penetrating items and the
perimeter of the opening. During a fire, the intumescent component
within each pillow dramatically exPass and Seymourto seal the opening
from fire, thereby maintaining the integrity of the fire separation.
NSi Fire Stop Pillows consist of an intumescent layer sandwiched
between non combustible insulation, all enclosed in a hermetically
sealed polyethylene shell. No sealant or putty is required. Easy to
install, easy to remove and a quick and clean installation. ASTM E
814 and UL 1479.
View Spec's Here
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Quantity
Discount |
Purchase |
| FSP |
FireStop Pillow in 2" x 4" x 8" |
1-24 $14.65 |
25+ $13.91 |
|
|
FireStop Mineral Wool |
 NSi FireStop Mineral Wool is a pre-formed, non-combustible miner-al
wool insulation. It is a semi-rigid combination of basaltic mineral
wool and proprietary binders. The mineral wool is pre-cut into various
widths and depths in 48 inch lengths for ease of handling and
immediate installation. It is intended for use as a firestop system
component and forming material in tested firestop systems and
designs. It is friction fitted into openings, joints, gaps, spaces
and
voids in fire rated assemblies. It is usually used in con junction
with
firestop sealant products such as Silicone, Silicone SL and
Intumescent Caulk.
Install NSi FireStop Mineral Wool to the minimum 25% to 33%
compression
required by the tested firestop system. Compression must always be
perpendicular to
the grain. Butt adjacent sections of NSi FireStop Mineral Wool
tightly against each other. Leave
no voids. NSi FireStop Mineral Wool is the recommended backing
material for NSi FireStop
Silicone, Silicone SL and Intumescent Caulk. Determine the depth of
firestop sealant required and
recess the mineral wool to the appropriate depth.
** Please note
these products
are Ground Shipped Only ** |
| Cat
# |
Description |
Spec's |
Quantity
Discount |
Purchase |
| FSMW |
Mineral
Wool in 25 lb. bags |
View |
1-4 $103.95 |
5+ $93.55 |
|
|
View Technical
Information Here |
| Click
on Pictures for Pricing |
|
|
|
NSi
FireStop Systems include;
